Download PDF

We are specialized in offering a wide range of "VINITEC" make three Phase Sequence Corrector that is designed and constructed to meet the demands of sensitive three phase equipment. VINITEC using superior quality of raw material, Automatic Phase Sequence correctors prevent damages at the time when phase is changed or reversed.

• Suitable for correcting the Three phase sequence, whenever the sequence is changed or reversed.
• No break downs of Lifts, UPS, Machineries, 3 Ph. Air conditioner or any motors or 3-phase system due to any change in sequence.
• For Three Phase UPS, during sequence changed or reversed, UPS will start use the battery power & battery may become empty within half or one hour.
• 3 Ph air conditioner will be tripped off, due to sequence reversal & the entire office will be suffering or disturbed because of AC failure.
• Avoid damages during phase sequence changes or reversal.
• The sequence corrector will switch off, during the single phasing or imbalance voltage occur & later, auto-reset after restoration.

Download PDF

VINITEC has designed various type of voltage stabilizers to overcome the problem of voltage fluctuations effectively, Servo stabilizers are one of the best type of stabilizers and are used for dedicated electrical and electronic equipments, where the load needs a substantially constant voltage with close tolerance without introducing harmonic distortion.

• Computer/CNC Machine
• Plastic Molding Machinery
• Lifts
• Signaling / Telecom Equipment
• Printing Presses
• Scientific Equipment
• Electro Medical Equipment
• Air Conditioning Plant
• Oxygen Plant for Medical Use

VINITEC has designed various type of voltage stabilizers to overcome the problem of voltage fluctuations effectively, Servo stabilizers are one of the best type of stabilizers and are used for dedicated electrical and electronic equipments, where the load needs a substantially constant voltage with close tolerance without introducing harmonic distortion.

• Over load and short circuit protection
• Earth fault protection
• Low / High voltage cut-off
• Mobile Based Remote control Monitoring
• Single phase prevention/reverse phase
• Spike and surge protection
• Stabilizer By Pass System
• Auto Phase Correction in case of Phase Reversal

Download PDF

VINITEC Isolation range employees a unique multiple shielding technique that reduce the inter winding capacitance to below 0.009 pf and DC Isolation to over 100 Megaohms and line leakage current to a safe 10 microamps maximum. Attenuation of common mode noise is about 100dB.

VINITEC Isolation power Line Noise Isolator is and ultra-isolation transformer which prevents passage of line voltage transient, spikes and galvanic leakages from reaching sensitive of critical equipment, like Computers & its peripherals, Medical Instrumentation, Digital Communication and Telemetry systems etc.

• Complete Electrostatics Shielding.
• D.C. Insulation <1000 Megaohms.
• Minimizes Transverse Mode Noise.
• Line and Load Regulation better than ± 3.5%.
• Minimizing Common Mode Noise by Over 130 dB.
• Quality Components, Conservating Ratings and ruggedized design for best Long Term Value.

Download PDF

Download PDF

Download PDF

Download PDF

VINITEC AC Charger Benefits

• AC Charger
• DC Charger
• Combo Charger

Download PDF

RANGE: UP TO 15000 KVA IN 11 & 33 KV CLASS.

H.T. Automatic Voltage Stabilizers are used to get stabilized H.T. input voltage, irrespective of the voltage variations received from electricity supply authorities. Additionally, these stabilizers also prevent the transformer and other electrical equipment from getting overloaded. Wide voltage variation ranges are taken care continuously and in on load condition. The variations of more than ± 1% of the rated output voltage are sensed through solid state relay. This relay operates on 230 V, 110Ø supply and sends signals to the stabilizer's motor, which drives the roller mechanism in lower and higher direction to bring voltage to the rated output voltage within +- 1%. The Accuracy of +-1% may vary depending on the specific requirement of customer.

H.T. Automatic Servo Voltage Stabilizers have helical coils mounted on a conventional laminated core. Carbon rollers are assembled on a fibre glass carrier board and are traverse to the length of the coil track. The rollers are connected to the electric output terminals. Nearby the regulating coil, a number of compensating winding is connected in parallel, which are short circuited to reduce the effect of core-flux fringing. It also keeps the reactance of the regulator constant at any position of the rolling contact.

These HT-Automatic Voltage Regulators are widely used in different industrial sectors for getting a stable input voltage.

• Generally H. T. Automatic Voltage Regulator consist of two tanks to facilitate servicing of the moving parts of Rolling Contacts and other components in the regulator without disturbing the main tank containing Transformers
• Isolates Sensitive Equipment's from Noisy Power Lines
• Carbon rollers goes around the length of the coil track & are assembled on a fiber glass carrier board
• The rollers are connected to the electric output terminals
• Parallel connection of compensating winding near the regulating coil is done
• The connection between the windings and regulating coils is short circuited so as to reduce the effect of core-flux fringing
• It keeps the reactance of the regulator constant at any position of the rolling contact

• Utilization of the Distribution Transformer is to its full capacity as the H.T. AVR shares the load of the Transformer and the connected load
• Losses are less as the incoming voltage either low or high is corrected at the initial stage only
• Fluctuations in the H.T. Supply are not passed on to the Distribution Transformer
• Installation Cost is less in comparison to L.T. Automatic Servo Voltage Stabilizer, for higher ratings
• Single Unit of H.T. Automatic Servo Voltage Stabilizer can be connected to more than one Distribution Transformer
• Economical for huge capacities like 2500 KVA and above or for wide voltage fluctuation range (eg. 8 KV – 13 KV, 28 KV – 36 KV etc.)
• Can be placed anywhere on the feeder line
• Motor fitting is external, so any change of the motor or motor shaft can be easily done without opening the top cover
• Output Voltage of H.T. AVR remains constant at any connected Load and up to full load
• Response time for Voltage correction is 20 micro seconds
• Low replacement cost
• 5% to 10% saving on energy consumption
• Reduction in breakdown period of the machines
• 100% capacity
• On Load step-less voltage variation

• Very Easy to maintain - No Specialize Manpower is required
• Undistorted output characteristics ie. No wave from distortion
• Moving parts on L.T. side and its mass is extremely low, only few lb-inch torque
• Energy savings
• High efficiency (about 99%) and minimum no load losses
• Simplicity and flexibility of design
• On load stepless voltage variation
• Long service life
• Impulse tested
• Regulating coils are wound with rectangular conductors on their edge, thus giving high mechanical strength compared to other designs
• Low replacement cost

Download PDF

Rolling Contact Type Voltage Stabilizer is one powerful boon by the technology that is used to overcome the problems of electricity fluctuation. These are extensively used in various industrial applications and have proved their worth through their extensive performance and quality services.

It is an essential and extremely relevant part of the manufacturing or industrial units that often faces electricity breakdowns/fluctuations. The main mechanism in the Rolling Contact Type Voltage Stabilizer is performed by the carbon rollers. These rollers rotate whenever the other component moves up and down. Due to this continuous movement, the point of contact changes every time, which ensures the durability of the carbon rollers.

The efficiency of these stabilizers is very high. The winding of the stabilizer is done through a copper strip, which allows it to carry a high-capacity current. A high-quality rolling contact type stabilizer is a one-time investment, which lasts for a long period, around 20 years. At Vinitec, we ensure that you receive the best service from the stabilizers we deliver, hence we manufacture them, keeping the high standards in mind.

• Over Voltage & Low Voltage Cut Off
• Over Load Cut Off
• Short Circuit Protection
• Phase Reversal Protection
• Phase Fail Protection
• By Pass Arrangement

Download PDF